Earthquaker Devices Pyramids Stereo Flanging Device Guitar Effects Pedal with Flexi Switch

Earthquaker Devices Pyramids Stereo Flanging Device Guitar Effects Pedal with Flexi Switch

Earthquaker Devices Pyramids is a Stereo Flanging Device with five presets, eight flanger modes, tap tempo, tap subdivision, a multifunction Modify control, positive and negative Feedback, and a variable Mix control, which is something you don’t see on a flanger every day.
Exquisite Sound
Built upon the same proprietary DSP architecture as the Avalanche Run, Pyramids delivers a convincing jet-engine roar, authentic through-zero tape-style warble, infinite barber pole sweeps, flexible I/O routing, and the ability to re-trigger the LFO cycle via footswitch opens up a fourth dimension of rhythmic possibilities that’s sure to tickle your third ear.
Classic Mode
Tone control for the modulated signal. Clockwise cuts the low end and allows the high frequencies to pass through. Counterclockwise cuts the high end and allows bass frequencies to pass through.
Through-Zero Mode
Delay time for the unmodulated dry signal. This controls where in the LFO cycle the through-zero point occurs, which is where you’ll hear the most drastic cancellation.
Barber Pole Up and Down Mode
Tone control for the modulated signal. Clockwise from the center is a high pass filter. Counterclockwise from the center is a low pass filter. Tone control for the modulated signal. Clockwise from the center is a high pass filter. Counterclockwise from the center is a low pass filter.
Trigger Up and Down Mode
Sensitivity control for the sweep. This controls how quickly the re-triggering reacts to your pick attack. Sensitivity control for the sweep. This controls how quickly the re-triggering reacts to your pick attack.
Step Mode
Adjusts the glide between steps. Low Modify settings produce sharp, stair-stepped transitions between steps. Higher Modify settings introduce a smoother glissando effect.
Random Mode
Adjusts the glide between steps. Low Modify settings produce sharp, stair-stepped transitions between steps. Higher Modify settings introduce a smoother glissando effect.
Controls
Manual controls the delay time of the modulated signal. Manual can also be controlled via the expression pedal. Rate controls the speed of the LFO as well as the rise time in ‘Trigger Up’ mode and fall time in ‘Trigger Down’ mode. The Rate control has three ranges of operation: Slow, Normal, and Fast. These modes are selected by the Rate and Tap toggle switch. Width controls the frequency range of the LFO sweep. You might also think of it as a depth control for the LFO. Mix controls is the volume control for the modulated signal. The modulated signal gets louder when you turn it clockwise and quieter when you turn it counterclockwise. Activate Footswitch features the Flexi-Switch technology. This relay-based true-bypass switch allows for momentary or latching operation. Feedback regeneration control for the modulated signal. Rate and Tap Toggle Switch ‘Normal’ center position is 1:1. The tempo you tap in is the tempo Pyramids will spit out. When set to ‘Slow’ left position, the tempo you tap is divided for a slower sweep. When set to ‘Fast’ right position, the tempo you tap is multiplied and delivers a faster sweep. Modify the behavior of this control depends upon which mode you’re using. Tap and Trigger Footswitch In Classic, Through-Zero, Barber Pole Up, Barber Pole Down, Step, and Random modes, this footswitch is a tap tempo control. In Trigger Up and Trigger Down modes, this footswitch triggers the effect whenever it is pressed. Presets Rotary Switch selects between Live mode and one of five presets. Pyramids come with the favorites programmed in, but you’re allowed to re-write them if you want. Mode Rotary Switch selects between Pyramids’ eight-flanger mode. Pyramids ships with five example factory presets, Classic, Barber Pole Up, Trigger Up, Step and Random. These are intended to get you started and are by no means the be-all-end-all examples of these modes. Please feel free to modify or overwrite these as you’d like.
Use Pyramids in Mono
Plug your instrument into the left input and use either the left output or the right output.
Use Pyramids with a Mono Input and Stereo Output
Plug your instrument into the left input and connect both the left output and right output to the next stereo pedal in your chain, to two inputs of your DAW, or to two amplifiers.
Use Pyramids with a Mono Input and Stereo Output
Plug your instrument into the left input and connect both the left output and right output to the next stereo pedal in your chain, to two inputs of your DAW, or to two amplifiers.